Free consultation
Required tools:
Minimum tools required for successful installation of flexible tile
Primer roller
6 mm notched trowel
Flat trowel
Putty knife
Ruler
Tape measure
Utility knife
Sponge
Pigment, grout, and adhesive
How to choose the right materials for the tile shade and substrate type
Surface preparation:
- Cleaning the walls from dust and dirt
- Checking the walls for flatness, cracks, and voids
- Leveling the surface (if required)
- Priming for better adhesion
Choosing the pigment
- Selected based on the tile color and the type of adhesive (white or gray)
- Added to the dry adhesive and mixed thoroughly
- Shades: beige / gray / anthracite
Small
2 bags
2 bags
Large
5–10 bags
5–10 bags
Choosing the grout
- The color is selected to match the tile
- Prepared before use
- Available in several colors and packaging options:
Small
300 g
300 g
Large
1 kg
1 kg
Choosing the adhesive
- For light stone shades – adhesive based on white cement
- For dark stone shades – adhesive based on gray cement
- For faсades – frost-resistant adhesive
Important!
The adhesive consistency should be slightly thinner than standard tile adhesive for better bonding.
The adhesive consistency should be slightly thinner than standard tile adhesive for better bonding.
Choosing the pigment
- Selected based on the tile color and the type of adhesive (white or gray)
- Added to the dry adhesive and mixed thoroughly
- Shades: beige / gray / anthracite
Small
2 bags
2 bags
Large
5–10 bags
5–10 bags
Choosing the grout
- The color is selected to match the tile
- Prepared before use
- Available in several colors and packaging options:
Small
300 g
300 g
Large
1 kg
1 kg
Choosing the adhesive
- For light stone shades – adhesive based on white cement
- For dark stone shades – adhesive based on gray cement
- For faсades – frost-resistant adhesive
Important!
The adhesive consistency should be slightly thinner than standard tile adhesive for better bonding.
The adhesive consistency should be slightly thinner than standard tile adhesive for better bonding.
Choosing the primer depending
on the type of surface:
on the type of surface:
Minimum tools required for the successful installation of flexible tiles
Important! After applying concrete contact primer, the surface becomes rough, which improves the adhesion of the adhesive.
Absorbent surfaces
use a deep penetration primer
Putty
Sandstone
Limestone
Low-absorbency surfaces
– concrete contact primer with quartz sand
Plastic
Glass
Concrete
Metal
Recommendations for facade surfaces made of OSB or sandwich panels
For the installation of Pletaflex flexible tiles on facade surfaces made of OSB or sandwich panels, the specific properties of these materials must be taken into account. They require additional preparation to ensure strong adhesion and long-lasting cladding.
Important! This approach will ensure reliable fastening of the flexible tiles and extend their service life on façade surfaces.
Temperature conditions:
Follow the adhesive manufacturer’s guidelines.
Avoid installation in frost.
In hot weather, dampen the surface so the adhesive does not dry too quickly.
Steps for installing flexible stone:
Tip: Work in pairs — one applies the adhesive, the other installs the tile and removes excess.
1
Adhesive application
– with a notched trowel (4–8 mm for smooth tiles, 6 mm for textured ones)
2
Tile installation
press firmly with a float to remove air
3
Removing excess adhesive
using a damp sponge
4
Finishing
coating quality control
Common installation mistakes and how to fix them
Follow the instructions at every stage of flexible stone installation to avoid future facade problems.
Adhesive layer too thick or too thin
Apply an even layer with a notched trowel.
Poor wall preparation
Be sure to clean and prime the surface.
Ignoring temperature conditions
Monitor humidity and air temperature during installation.
Advantages of installing
Kordeko flexible tiles
Easy installation
Fast installation without complex tools or dust.
Savings on installation.
Reduces labor costs and speeds up the entire finishing process.
Minimal preparation.
Suitable for various substrates without complex preparation.
For complex surfaces.
Easily installed on arches, corners, and other complex elements.
Clean installation
Installation is carried out without excessive dust and without a large amount of waste.
Reliable fastening.
The material is firmly fixed to the surface and adheres well.
Quick installation.
Installation takes less time than the installation of many traditional materials.
Ease of use.
The material is easy to cut, fit, and glue without extra effort on site.